Comments
OSPF Fundamentals
OSPF is a link state routing protocol that updates the routing table only when network changes occur, rather than at a predefined interval. OSPF supports variable length subnet masks (VLSM) and route summarization.
OSPF routers and links are grouped logically into areas that are identified by assigned numbers. All OSPF networks have at least one area with the default being area 0. If more than one area exists, area 0 is defined as the backbone area and is used to connect all other areas. Each area has its own link state databases.
OSPF Areas Types
Normal Areas: These areas can either be standard areas or transit (backbone) areas. Standard areas are defined as areas that can accept intra-area, inter-area and external routes. The backbone area is the central area to which all other areas in OSPF connect.
Note: Intra-area routes refer to updates that are passed within the area. Inter-area routes refer to updates that are passed between areas. External routes refer to updates passed from another routing protocol into the OSPF domain by the Autonomous System Border Router (ASBR).
Stub Areas: These areas do not accept routes belonging to external autonomous systems (AS); however, these areas have inter-area and intra-area routes. In order to reach the outside networks, the routers in the stub area use a default route which is injected into the area by the Area Border Router (ABR). A stub area is typically configured in situations where the branch office need not know about all the routes to every other office, instead it could use a default route to the central office and get to other places from there. Hence the memory requirements of the leaf node routers is reduced, and so is the size of the OSPF database.
To define an area as a stub area, use the OSPF router configuration command, area
stub
Totally Stub Areas: These areas do not allow routes other than intra-area and the default routes to be propagated within the area. The ABR injects a default route into the area and all the routers belonging to this area use the default route to send any traffic outside the area.
To define a totally stub area, use the OSPF router configuration command, area
stub no-summary, on the ABR.
NSSA: This type of area allows the flexibility of importing a few external routes into the area while still trying to retain the stub characteristic. Assume that one of the routers in the stub area is connected to an external AS running a different routing protocol, it now becomes the ASBR, and hence the area can no more be called a stub area. However, if the area is configured as a NSSA, then the ASBR generates a NSSA external link-state advertisement (LSA) (Type-7) which can be flooded throughout the NSSA area. These Type-7 LSAs are converted into Type-5 LSAs at the NSSA ABR and flooded throughout the OSPF domain
To define a NSSA, use the OSPF router configuration command, area
nssa no-summary.
For more information on NSSA, refer to OSPF Not-So-Stubby Area.
Normal, Stub, Totally Stub and NSSA Area Differences:
Restriction
Normal
None
Stub
No Type 5 AS-external LSA allowed
Totally Stub
No Type 3, 4 or 5 LSAs allowed except the default summary route
NSSA
No Type 5 AS-external LSAs allowed, but Type 7 LSAs that convert to Type 5 at the NSSA ABR can traverse
NSSA Totally Stub
No Type 3, 4 or 5 LSAs except the default summary route, but Type 7 LSAs that convert to Type 5 at the NSSA ABR are allowed
Refer to the Types of OSPF Areas section of How Does OSPF Generate Default Routes? to learn more about different types of areas.
OSPF Router Types
Internal Router: Responsible for maintaining a current and accurate database of subnets within the area. Forwards data to other networks using the shortest path.
Backbone Router: Has an interface connected to the backbone (Area 0).
Area Border Router (ABR): Has interfaces in multiple areas with at lest one interface in area 0. Connects other areas to the backbone and maintains routing information for each connected area.
Autonomous System Boundary Router (ASBR): Router located between OSPF autonomous system and a non-OSPF network. Used to redistribute routing information between networks. Must reside in a non-stub area. Also, a router becomes an ASBR when OSPF is redistributing from other routing protocols, including static routes, and it may reside in a pure OSPF network.
OSPF LSA Types
Type 1: Router link advertisements generated by each router for each area it belongs to. Flooded to a single area only (intra-area route). In a multiarea OSPF network, routes, originated within an area, are known by the routers in the same area as Intra-Area routes. These routes are flagged as O in the “show ip route” command output.
Type 2: Network link advertisements generated by designated routers describing the set of routers attached to a particular network. Flooded to the area that contains the network (intra-area route). When a route crosses an OSPF Area Border Router (ABR), the route is known as an OSPF Inter-Area route. These routes are flagged as O IA in the “show ip route” command output.
Both Intra and Inter-Area routes are also called OSPF Internal routes, as they are generated by OSPF itself, when an interface is covered with the OSPF network command.
Type 3/4: Summary link advertisements generated by ABRs describing inter-area routes. Type 3 describes routes to networks and is used for summarization. The "default-information originate" is also Type 3. Type 4 describes routes to the ASBR (interarea summary route).
Type 5: Generated by the ASBR and describes links external to the Autonomous System (AS). These are the redistributed (from other routing protocols including static routes) routes. Flooded to all areas except stub areas (external route). Routes which were redistributed into OSPF, such as Connected, Static, or other Routing Protocol, are known as External Type-2 or External Type-1. These routes are flagged as O E2 or O E1 in the “show ip route” command output.
Type 6: Group membership link entry generated by multicast OSPF routers.
Type 7: NSSA external routes generated by ASBR. Only flooded to the NSSA. External routes injected internally by ASBRs within each POP (Areas other than Area 0) are LSAs of type 7. The ABR between will translate LASs type 7 to LSAs type 5 from each POP/Area to Area 0 (external route). When an area is configured as a Not-So-Stub Area (NSSA), and routes are redistributed into OSPF, the routes are known as NSSA external type 2 or NSSA external type 1. These routes are flagged as O N2 or O N1 in the “how ip route” command output.
Posted by jahangir1983
The router ABR is used
Posted by HamidAliKhan
ABR is used
Posted by waqqas1
In an OSPF network it doesn't implies the area as 2 distinctive entities. Let's take an example Area2>>>Area0>>Area1>>>Area3. OSPF protocol restricts the use of non backbone areas must be connected to a backbone area with an exception of virtual links. Consider the connectivity between Area3 to Area0 as virtual link.
The SPF calculation with in area will consider only the routes reachable specific to that area, ie ospf calculates route reachability specific to that area, once an ospf router has the routing table converged for a specific area it sends the updates to other areas similar to what distance vector protocol does. OSPF routers with atleast two interfaces in 2 different areas is an ABR, here Area3>>>Area1 that means atleast one of the routers must be part of both Area3 and Area1, same with Area2 and Area0. Assume s0/0 is Area1 and S0/1 in Area3 so this is an ABR and will send updates towards both sides.
If you are sending/receiving the updates to different AS or protocol then its an ASBR. This could be sending/receving reachability to the ISP or with in your domain by redistributing to different protocol.
Posted by John
On an OSPF network, when a packet needs to traverse from one area to another area to reach its destination, it is routed as below:
Source Area -> Source ABR -> Backbone Area -> Destination ABR -> Destination Area Routers.
Posted by priyadarshan
-