4 Knowledge Base

 

 TelecomTrainning.net > Knowledge Base
 Viewing KB Article
Good Morning, - Please register or - log-in to your account.
Search
Search   Saved Questions   Ask a question
Keywords 
 
Available categories
LTE
100 of Questions in LTE
CCNA Certification
CCNA Sample Q & A (1000 + Q &A)
(Network +) Certification
(Network +) Sample Q & A (1000 + Q &A)
Networking
General/Interview Q& A on Networking
Home Networking
General/Interview Q& A on Networking
VOIP, SIP & Asterisk
Q & A on VOIP,Ethereal, SIP & Asterisk
Telecom Test Equipments
Q & A on Telecom Test Equipment
PSTN / Wireline
General / Interview Q & A on PSTN / Wireline
LTE, Wireless, 3G ,Diameter and HSS
General/Interview Q & A on LTE, Wireless, 3G ,Diameter and HSS
Telecom General
Any Q & A in Telecom in General

Top Questions
Friends, Describe Secure storage and distribution of A-Keys?
what is the difference between E1 signal & Ethernet signal ?
How do I monitor SS7 Traffic in spectra2?
Can you tell me about PBGT?
Explain me the difference between a repeater, bridge and router? Relate this to the OSI model.
What is the difference between BRI & PRI ?
Guys what is the purpose of Umbrella Cell Approach in GSM ?
how can we explain media gateway in MSc?
What is the difference between Electrical-tilt and Mechanical-tilt of an antenna?
What is GGSN?
What is BSC?
What is demarc point?
Can any one explain me how sms flow will work using ss7 network ?( from physical layer to application layer)
why cellphone towers are painted in red and white?
Explain SLTA and SLTM messages in MTP3?
Hi guys what is WAP?
wat is the difference betweem MSC & GMSC, & MSS & GCS?
what is EDAp? what is the functions of EDAP?
What is a circuit id?
what is sdh?

How to Disable Messenger Service?
bretpark 01-October-2008 01:55:27 PM

Comments


Click Start and then click Control Panel.
Click Performance and Maintenance. (If you do not see the Performance and Maintenance icon, you may be using Classic View. You can skip to step 3 below, but you must double-click Administrative Tools.)
Click Administrative Tools.
Double-click Services
Double-click Messenger.
And Click on Stop
Posted by saqlain231


Click Start and then click Control Panel.
Click Performance and Maintenance. (If you do not see the Performance and Maintenance icon, you may be using Classic View. You can skip to step 3 below, but you must double-click Administrative Tools.)
Click Administrative Tools.
Double-click Services
Double-click Messenger.
In the Startup type list, choose Disabled
Click Stop, and then click OK.
Posted by waqasahmad


- Click start -> run -> cmd -> Command Prompt.
- Type net sends 127.0.0.1
- If you receive not supported or could not be found on the network, its okay. If you receive a pop-up then disable the service.

Posted by vishwesh


1.
Click Start and then click Control Panel.

2.
Click Performance and Maintenance. (If you do not see the Performance and Maintenance icon, you may be using Classic View. You can skip to step 3 below, but you must double-click Administrative Tools.)

3.
Click Administrative Tools.

4.


Double-click Services

5.
Double-click Messenger.

6.

In the Startup type list, choose Disabled

7.
Click Stop, and then click OK.
Posted by sagitraz

Q&A Rating

Q&A Rating
Rate This Question and Answer

Related Questions
What is the TMSI?
 
Guys,What is a T coder?
Tell About the correct syntax to configure a router as a BGP?
 


Search questions via popularity
Top viewed questions  Top emailed questions  Most printed questions  Most saved questions
 
Copyright © Telecom Training, All Rights Reserved