If synchronisation between BSC to BTS fail,what will happen?
sarathy_26 20-August-2008 03:34:24 PM
Comments


If Synchronization fails between BSC and BTS, the clock signal from BSC will not reaches to BTS and Abis link goes down and supervision not possible and we cant perform any operations at that site.
Posted by sagitraz


If yhe link is down ,then we use 2nd link ..means we use other bsc.we conect our bts with other bsc also.simply is that
Posted by saqlain231


The whole communication could create a mess.And blocks whole communication.
Posted by sagitraz


The whole communication could create a mess.And blocks whole communication.
Posted by sagitraz


Basically a fluctuation in Abis link and you can check it through a simple LED or with a BERT meter & you can also called it that LAPD is in break.
Posted by jahangir1983


Basically a fluctuation in Abis link and you can check it through a simple LED or with a BERT meter & you can also called it that LAPD is in break.
Posted by jahangir1983


If BTS-B fails to allocate resources to the MS, resources at BTS-A will not be .... to the MS after synchronization between the MS and BTS-B is achieved,A BTS will cover a specific geographical area depending on the location and ... If an MSC also acts as a switching centre between the PLMN
Posted by waqasahmad


If Synchronization fails between BSC and BTS, the clock signal from BSC will not reaches to BTS and Abis link goes down and supervision not possible and we cant perform any operations at that site.
Posted by yellaiah


In short when BTS link fail with BSC then an critical alarm is generated at the MSC end which is basically RED alert that communication is break and the channels are not available through that BTS
Posted by HamidAliKhan


Simply your whole communication is disturb.
Posted by waqqas1


Posted: 21-August-2008 01:01:11 AM By: sajit4134

BSC gets the time clock signals from three sources:
1. E1 clock.(SSP / Transport)
2. GPS Clock.
3. Internal Crystal Clock.

If all the three clock fails then there is no signalling possible between SSP, BSC & BTS. Hence calls will not mature but mobiles will show coverage. BTS's connected to that particular BSC will be affected.

Posted: 15-November-2008 02:31:44 AM By: Hash007

Its basically a fluctuation in Abis link and you can check it through a simple LED or with a BERT meter & you can also called it that LAPD is in break.

Posted: 15-November-2008 09:58:59 AM By: waqqas1

Simply your whole communication is disturb.

Posted: 17-November-2008 06:44:00 AM By: HamidAliKhan

In short when BTS link fail with BSC then an critical alarm is generated at the MSC end which is basically RED alert that communication is break and the channels are not available through that BTS

Posted: 25-December-2008 04:02:05 AM By: yellaiah

If Synchronization fails between BSC and BTS, the clock signal from BSC will not reaches to BTS and Abis link goes down and supervision not possible and we cant perform any operations at that site.

Posted: 31-January-2009 11:52:08 AM By: waqasahmad

If BTS-B fails to allocate resources to the MS, resources at BTS-A will not be .... to the MS after synchronization between the MS and BTS-B is achieved,A BTS will cover a specific geographical area depending on the location and ... If an MSC also acts as a switching centre between the PLMN

Posted: 31-January-2009 12:08:21 PM By: jahangir1983

Basically a fluctuation in Abis link and you can check it through a simple LED or with a BERT meter & you can also called it that LAPD is in break.

Posted: 31-January-2009 12:09:45 PM By: jahangir1983

Basically a fluctuation in Abis link and you can check it through a simple LED or with a BERT meter & you can also called it that LAPD is in break.

Posted: 21-March-2009 08:55:57 AM By: sagitraz

The whole communication could create a mess.And blocks whole communication.

Posted: 21-March-2009 08:56:02 AM By: sagitraz

The whole communication could create a mess.And blocks whole communication.

Posted: 06-June-2009 06:13:27 AM By: saqlain231

If yhe link is down ,then we use 2nd link ..means we use other bsc.we conect our bts with other bsc also.simply is that

Posted: 28-September-2009 07:32:45 AM By: sagitraz

If Synchronization fails between BSC and BTS, the clock signal from BSC will not reaches to BTS and Abis link goes down and supervision not possible and we cant perform any operations at that site.