Knowledge Base

2 Knowledge Base

Article Listings

Good Morning, - Please register or - log-in to your account.

LTE

100 of Questions in LTE

CCNA Certification

CCNA Sample Q & A (1000 + Q &A)

(Network +) Certification

(Network +) Sample Q & A (1000 + Q &A)

Networking

General/Interview Q& A on Networking

Home Networking

General/Interview Q& A on Networking

VOIP, SIP & Asterisk

Q & A on VOIP,Ethereal, SIP & Asterisk

Telecom Test Equipments

Q & A on Telecom Test Equipment

PSTN / Wireline

General / Interview Q & A on PSTN / Wireline

LTE, Wireless, 3G ,Diameter and HSS

General/Interview Q & A on LTE, Wireless, 3G ,Diameter and HSS

Telecom General

Any Q & A in Telecom in General

Top Questions
Friends, Describe Secure storage and distribution of A-Keys?
what is the difference between E1 signal & Ethernet signal ?
How do I monitor SS7 Traffic in spectra2?
Can you tell me about PBGT?
Explain me the difference between a repeater, bridge and router? Relate this to the OSI model.
What is the difference between BRI & PRI ?
Guys what is the purpose of Umbrella Cell Approach in GSM ?
how can we explain media gateway in MSc?
What is GGSN?
What is the difference between Electrical-tilt and Mechanical-tilt of an antenna?
What is BSC?
What is demarc point?
Can any one explain me how sms flow will work using ss7 network ?( from physical layer to application layer)
why cellphone towers are painted in red and white?
Explain SLTA and SLTM messages in MTP3?
Hi guys what is WAP?
wat is the difference betweem MSC & GMSC, & MSS & GCS?
what is EDAp? what is the functions of EDAP?
What is a circuit id?
what is sdh?

CCNA Certification

Hi,What are Cross-reference commands for Cisco and Nortel? telecom - 21-September-2009 10:28:06 PM Hi,What is clear channel coding? sagitraz - 19-September-2009 02:27:58 AM Which command verifies the placement and direction of an access list? michaelcoyne - 17-September-2009 01:21:16 AM write the command to apply the named access list you created to an interface.??? vishwesh - 17-September-2009 01:14:17 AM write the same standard IP access list as a named access list.??? elvin - 17-September-2009 01:13:21 AM What command would you use to set an access list on a VTY line? elvin - 17-September-2009 01:10:30 AM What command would you use to create an extended access list that stops host 172.16.10.1 from telnetting to host 172.16.30.5? bretpark - 17-September-2009 01:09:38 AM Which two commands verify that the access list was properly applied to the Ethernet interface? bretpark - 17-September-2009 01:03:08 AM Which command verifies that you�ve entered the access list correctly? areil - 17-September-2009 01:01:36 AM What command would you use to create an access list that denies host 192.168.15.5 access to an Ethernet network? areil - 17-September-2009 12:52:21 AM
Page: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63

Search questions via popularity
Top viewed questions Top emailed questions Most printed questions Most saved questions

	Help - TERMS - PRIVACY - CONTACT US - ABOUT US - RFP XML FEED - CURRENCY CONVERTER - TOP
Copyright © Telecom Training, All Rights Reserved