Knowledge Base

- Login to Change settings
- Login to View Points

2 Knowledge Base

TelecomTrainning.net

Article Listings

Good Evening, - Please register or - log-in to your account.

Search Saved Questions Ask a question

LTE

100 of Questions in LTE

CCNA Certification

CCNA Sample Q & A (1000 + Q &A)

(Network +) Certification

(Network +) Sample Q & A (1000 + Q &A)

Networking

General/Interview Q& A on Networking

Home Networking

General/Interview Q& A on Networking

VOIP, SIP & Asterisk

Q & A on VOIP,Ethereal, SIP & Asterisk

Telecom Test Equipments

Q & A on Telecom Test Equipment

PSTN / Wireline

General / Interview Q & A on PSTN / Wireline

LTE, Wireless, 3G ,Diameter and HSS

General/Interview Q & A on LTE, Wireless, 3G ,Diameter and HSS

Telecom General

Any Q & A in Telecom in General

Top Questions
Friends, Describe Secure storage and distribution of A-Keys?
what is the difference between E1 signal & Ethernet signal ?
How do I monitor SS7 Traffic in spectra2?
Can you tell me about PBGT?
Explain me the difference between a repeater, bridge and router? Relate this to the OSI model.
What is the difference between BRI & PRI ?
Guys what is the purpose of Umbrella Cell Approach in GSM ?
how can we explain media gateway in MSc?
What is GGSN?
What is the difference between Electrical-tilt and Mechanical-tilt of an antenna?
What is BSC?
What is demarc point?
Can any one explain me how sms flow will work using ss7 network ?( from physical layer to application layer)
why cellphone towers are painted in red and white?
Explain SLTA and SLTM messages in MTP3?
Hi guys what is WAP?
wat is the difference betweem MSC & GMSC, & MSS & GCS?
what is EDAp? what is the functions of EDAP?
What is a circuit id?
what is sdh?

CCNA Certification

Help me what are advantages to segmenting your network with routers? Barrett - 07-September-2007 06:30:39 PM I need help; what do you need to support full-duplex Ethernet? Titus - 07-September-2007 06:30:25 PM Hi how do I set the frame relay interface si bandwidth to 56 Kbps? Chandler - 06-September-2007 06:30:04 PM Anyone tell me, what is the primary characteristic of a connection-oriented (reliable) protocol? Haden - 06-September-2007 06:29:47 PM Friends I have a doubt that, entering a static IP route and you type the following command: ip route 172.16.1.0 255.255.255.0 172.16.2.1 120 What does the "172.16.2.1" mean? Harold - 06-September-2007 06:29:29 PM Hi guys you are entering a static IP route and you type the following command: ip route 172.16.1.0 255.255.255.0 172.16.2.1 110 What does the "110" at the end mean? Chaim - 06-September-2007 06:28:30 PM Friends what commands provide route verification? Terrell - 06-September-2007 06:28:13 PM Friends I have a doubt that, a switching facility that provides the nearest point of presence for a providers WAN service is called? Thomas - 06-September-2007 06:27:59 PM Hello friends, if you enter the shutdown command on a particular interface, and then enter a show interface command, what will the status line say? Luciano - 06-September-2007 06:27:26 PM Hi guys i want to create an access list to permit only the subnets 161.130.16.0 through 161.130.31.0. Assume the default subnet mask. What wildcard mask would you use? Camron - 06-September-2007 06:27:07 PM
Page: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63

Search questions via popularity
Top viewed questions Top emailed questions Most printed questions Most saved questions

	Help - TERMS - PRIVACY - CONTACT US - ABOUT US - RFP XML FEED - CURRENCY CONVERTER - TOP
Copyright © Telecom Training, All Rights Reserved